“Which design is preferred over other; Synchronous or Asynchronous?”
Idea Solution:-
This link and material can help a lot.
http://electronicsbus.com/synchronous-vs-asynchronous-digital-design/ and
Applications of Asynchronous Digital Logic
Every Digital Electronics engineer prefers synchronous logic due to many well known reasons. But there are some exceptional cases where asynchronous logic offers best solution compared to synchronous digital logic. These exceptions, however, must be designed with extreme caution and only as a last resort when a synchronous solution cannot be found.
Asynchronous Reset
There are times when an asynchronous reset is acceptable, or even preferred. If the vendor’s library includes asynchronously resettable flip-flops, the reset input can be tied to a master reset in order to reduce the routing congestion and to reduce the logic required for a synchronous reset. FPGAs and CPLDs will typically have master reset signals built into the architecture. Using these signals to reset state machines frees up interconnect for other uses.
Asynchronous reset should be used only for resetting the entire chip and should not occur during normal functioning of the chip. After reset, you must ensure that the chip is in a stable state such that no flip-flops will change until an input changes. You must also ensure that the inputs to the chip are stable and will not change for at least one clock cycle after the reset is removed.
Asynchronous Latches on Inputs
Some buses, such as the VME bus, are designed to be asynchronous. In order to interface with these buses, it is necessary to use asynchronous latches to capture addresses or data. Once the data is captured, it must be synchronized to the internal clock. However, it is usually much more efficient to use asynchronous latches to capture the data initially. Unless your chip uses a clock which has a frequency much higher than that of the bus, attempting to synchronously latch these signals will cause a large amount of overhead and may actually produce timing problems rather than reduce them.
Other Asynchronous Circuits
Occasionally, circuits are needed to operate before a clock has started running or when a clock has stopped running. Circuits that generate system resets, and watchdog circuits are examples of these. Every attempt should be made to design these circuits synchronously or move them off chip and use discrete chips whose worst case and best case timing is very explicitly defined. If this cannot be done, design these circuits with care and realize that changes to the semiconductor process may make your chip unusable.
Applications of Asynchronous Digital Logic
Every Digital Electronics engineer prefers synchronous logic due to many well known reasons. But there are some exceptional cases where asynchronous logic offers best solution compared to synchronous digital logic. These exceptions, however, must be designed with extreme caution and only as a last resort when a synchronous solution cannot be found.
Asynchronous Reset
There are times when an asynchronous reset is acceptable, or even preferred. If the vendor’s library includes asynchronously resettable flip-flops, the reset input can be tied to a master reset in order to reduce the routing congestion and to reduce the logic required for a synchronous reset. FPGAs and CPLDs will typically have master reset signals built into the architecture. Using these signals to reset state machines frees up interconnect for other uses.
Asynchronous reset should be used only for resetting the entire chip and should not occur during normal functioning of the chip. After reset, you must ensure that the chip is in a stable state such that no flip-flops will change until an input changes. You must also ensure that the inputs to the chip are stable and will not change for at least one clock cycle after the reset is removed.
Asynchronous Latches on Inputs
Some buses, such as the VME bus, are designed to be asynchronous. In order to interface with these buses, it is necessary to use asynchronous latches to capture addresses or data. Once the data is captured, it must be synchronized to the internal clock. However, it is usually much more efficient to use asynchronous latches to capture the data initially. Unless your chip uses a clock which has a frequency much higher than that of the bus, attempting to synchronously latch these signals will cause a large amount of overhead and may actually produce timing problems rather than reduce them.
Other Asynchronous Circuits
Occasionally, circuits are needed to operate before a clock has started running or when a clock has stopped running. Circuits that generate system resets, and watchdog circuits are examples of these. Every attempt should be made to design these circuits synchronously or move them off chip and use discrete chips whose worst case and best case timing is very explicitly defined. If this cannot be done, design these circuits with care and realize that changes to the semiconductor process may make your chip unusable.
Please do make changes in these assignment otherwise every one who copy this assignment as it is will awarded zero marks
NOTE: - These Assignments OR Quiz are just for idea, so kindly don't copy it, after viewing it make your own. Thanks We always try our best to upload 100% correct solution BUT it is requested that you kindly review it before submission, please BEST OF LUCK, Thanks to those students those send me Assignments and quizzes. If you have any Assignment and quiz kindly send at fascobuk@gmail.com 
